Industrial baking Oven




Heating elements is provided in independent sets, each connected for 3 phase operation. The heating elements is so distributed as to ensure even heating throughout the oven, at any combination of elements decided by the controller. Also, the electrical load on the system is at all times be a balanced on 3 phase load. Manually operated control switches are provided for disconnection to some of the sets of heating elements for obtaining low or high heat as desired. The automatic temperature controller is provided. Two Nos. Of thermocouple are provided on two opposite side walls with some length of compensating cables. The tips are corrosive resistant to varnish fumes and replaceable type. A safety thermostat is provided to switch off and look out the supply to heating elements. It is a possible to adjust the thermostat to 10 °C above required working temperature. Indicating Lamps for Various indications are provided. 

Product Details:

  • The electric oven will be used for drying and baking of Varnish in Motors and Transformers such as shall be suitable for continues operation
  • The oven shall be suitable for operation on 400/440 Volts, 3 Phase, 50 Hz AC supply, 4 Wire System
  • The temperature of oven outer wall shall not be more than 15 °C above the ambient during continuous operation of the oven at 250 °C
  • The working temperature in the oven shall be adjustable to any required value between 50 °C to 250 °C.
  • The tolerance on the working temperature at any setting is plus or minus 3 °C.
  • The maximum difference between temperatures measured at any two points inside oven shall not be more than 5 °C
  • The temperature in the oven shall be maintained automatically within required range by means of the temperature controller provided


The capacity of the heating element is adequate for:

  • Raising the temperature of the empty oven from 25 °C to 250 °C in two hours
  • Raising the temperature of the oven charged with Transformers from 25 °C to 250 °C in 5 hours
  • Maintaining the oven temperature at 250 °C at ambient temperature of 25 °C taking into consideration the leakage


Technical Specifications:

  • Voltage : 415 V 3 Phase 50 Hz


The inside dimension of the oven will be as follows:

  • Width - 2000 mm
  • Height - 1500 mm
  • Depth - 2000 mm

Industrial Drying Oven




Industrial Drying Oven and equipment could become a tough job if the knowledge on the tools and brands available is not sufficient. We make your job simpler by being able to offer a wide variety of choices based on cost, brand and country of manufacture. Choosing the right tool for the right job is very important. Otherwise it could damage the part / job you are working on.

Product Details:


  • The electric oven will be used for drying of transformer breather silica gel which will be suitable for continuous operation
  • The oven will be suitable for operation on 400/440 Volts, 3 Phase, 50 Hz AC supply, 4 Wire System
  • The temperature of oven outer wall will not be more than 15 °C above the ambient during 150 °C
  • The tolerance on the working temperature at any setting will be plus or minus 3 °C
  • The maximum difference between temperatures measured at any two points inside oven will not be more than continuous operation of the oven at 150 °C
  • The working temperature in the oven will be adjustable to any required value between 50 °C to 5 °C


Technical Specifications:

 

  • Operating voltage: 415V, Three Phase, 50Hz
  • Rating: 40 - 240°C
  • Total weight without Silica Gel approx: 300 Kg
  • Voltage: 415 V 3 Phase 50Hz
  • Weight of the Silica Gel load: 20 Kg
  • Heating resistances power: 6 kW

 


The inside dimension of the oven will be as follows:

 

  • Width - 500 mm
  • Height - 500 mm
  • Depth - 500 mm